Tag: #dsPIC33Tutorial

dsPIC/PIC24 UART without DMA (using XC16 and MPLAB X)

UART in 16bit controllers (dsPIC and PIC24) has a FIFO buffer for their receive and transmit buffers. In 8 bit variants the buffer size is 1 byte. For the PIC I’m using (dsPIC33FJ128GP202) it is 4 bytes and may change with different parts (please read the data sheet for RX and TX buffer size). The peripheral library will take care of the buffer for the most part but not always. So just be careful.

In this post I am giving the code snippet without using the DMA feature. Next post I’ll make one with the DMA feature.

`

Documents to read

 

    I am using dsPIC33FJ128GP202 (28 pin SOIC package). Given below is the image that shows which pin I’m setting in for the TX.
    TX

I’m using pin 22 (RB11) as UART TX pin.

 

Steps to setup UART

 

  • Set the TRIS bits
  • Set the PPS for the RP pin
  • Setup UART settings
Note: UART has TX FIFO buffer whose size can be found by reading the datasheet. If UART prints only up to maximum FIFO buffer length, then it means TX buffer is full. Using putsUSARTx() function will take care of TX buffer while printing. For manually printing each character, TX buffer has to be handled properly (check the RX code).

 

UART Transmit Code

 

For the most part the comments tell what the settings do. Also the document DS70000582E ( http://ww1.microchip.com/downloads/en/DeviceDoc/70000582e.pdf) will help with a few code snippets too.

In the UART settings you got UART_BRGH_SIXTEEN. Another option is UART_BRGH_FOUR. The way this setting works is by deciding number of clock bits to sample per data bit. This is kind of new compared to the 8bit variants.

 

UxBRG calculation

 

baud

 

The above calculation is when defined as a macro, its easy to edit when the baud rate needs to be changed (snapshot below).

macro

 

The following code will print “Singular Engineer” every one second approximately.

/* * File: dsPICtest.c * Author: Singular Engineer * * Created on June 28, 2015 */ #define FCY 40000000ULL //Fcy = (Fosc/2); Fosc = 80MHz #include <xc.h> #include "config.h" #include <libpic30.h> #include <pps.h> #include <uart.h> #define BAUDRATE 115200 #define BRGVAL ((FCY/BAUDRATE)/16)-1 void SetupClock(void); void SetupIOPins(void); void InitUART1(void); void Delay1Second(void); char *TXData = "Singular Engineer \r"; int i = 0; int main() { SetupClock(); SetupIOPins(); InitUART1(); while(1) { putsUART1((unsigned int *)TXData); Delay1Second(); } } void InitUART1() { unsigned int UartMode = 0; unsigned int UartCtrl = 0; UartMode = UART_EN & //Enable UART UART_IDLE_CON & //Continue working when Idle UART_IrDA_DISABLE & //Not using IrDA UART_MODE_SIMPLEX & //Not using Flow control UART_UEN_00 & //Not using CTS/RTS pins by not setting it up UART_DIS_WAKE & //Disable wakeup option UART_DIS_LOOPBACK & //Not using in loopback mode UART_DIS_ABAUD & //Disable ABAUD UART_NO_PAR_8BIT & //8bit data with none for parity UART_BRGH_SIXTEEN & //Clock pulse per bit UART_1STOPBIT; // 1 stop bit UartCtrl = UART_TX_ENABLE & //Enable UART transmit UART_IrDA_POL_INV_ZERO; //VERY IMPORTANT - sets the pin's idle state OpenUART1(UartMode,UartCtrl, BRGVAL); } void SetupIOPins() { //--------------- Pin Assignment ----------------- TRISBbits.TRISB11 = 0; //Pin 22 as output pin for UART TX PPSUnLock; PPSOutput(OUT_FN_PPS_U1TX, OUT_PIN_PPS_RP11); PPSLock; //------------------------------------------------- } void Delay1Second() { for(i=0;i<100;i++) { __delay_ms(10); } } void SetupClock() { //Setting N1 to 4 (N1 = n+2); n = N1-2 CLKDIVbits.PLLPRE0 = 0; CLKDIVbits.PLLPRE1 = 1; CLKDIVbits.PLLPRE2 = 0; CLKDIVbits.PLLPRE3 = 0; CLKDIVbits.PLLPRE4 = 0; //Setting M to 32 (M = m+2); m = M-2 PLLFBDbits.PLLDIV0 = 0; PLLFBDbits.PLLDIV1 = 1; PLLFBDbits.PLLDIV2 = 1; PLLFBDbits.PLLDIV3 = 1; PLLFBDbits.PLLDIV4 = 1; PLLFBDbits.PLLDIV5 = 0; PLLFBDbits.PLLDIV6 = 0; PLLFBDbits.PLLDIV7 = 0; PLLFBDbits.PLLDIV8 = 0; //Setting N2 to 2 CLKDIVbits.PLLPOST0 = 0; CLKDIVbits.PLLPOST1 = 0; }

 

Output

 

image

 

UART Receive code

 

Similar to UART transmitter buffer, the UART receiver buffer is also 4 bytes deep FIFO buffer. So when you setup the interrupt, you got to keep in mind how you set the interrupt to be triggered.

rx_int_options

If the FIFO buffer is 4 bytes deep, then an interrupt will happen very 4th byte notifying that the RX buffer is full if UART_INT_RX_BUF_FUL option is selected. And so on. Here for this example I have made UART_INT_RX_CHAR which will trigger an interrupt for every character. If the received character contains a return character ( 0x0D in hex), then it will print everything or if it hits the max buffer size I set.

/* * File: dsPICtest.c * Author: Singular Engineer * * Created on June 28, 2015 */ #define FCY 40000000ULL //Fcy = (Fosc/2); Fosc = 80MHz #include <xc.h> #include <string.h> #include "config.h" #include <libpic30.h> #include <pps.h> #include <uart.h> #define BAUDRATE 115200 #define BRGVAL ((FCY/BAUDRATE)/16)-1 #define _ISR_AUTO_PSV __attribute__((__interrupt__, __auto_psv__)) void SetupClock(void); void SetupIOPins(void); void InitUART1(void); char *TXData = "Singular Engineer \r"; unsigned int RXData[32]; //To store Received data volatile unsigned int RXCnt = 0; volatile int i = 0; int main() { SetupClock(); SetupIOPins(); InitUART1(); while(1) { } } void InitUART1() { unsigned int UartMode = 0; unsigned int UartCtrl = 0; UartMode = UART_EN & //Enable UART UART_IDLE_CON & //Continue working when Idle UART_IrDA_DISABLE & //Not using IrDA UART_MODE_SIMPLEX & //Not using Flow control UART_UEN_00 & //Not using CTS/RTS pins by not setting it up UART_DIS_WAKE & //Disable wakeup option UART_DIS_LOOPBACK & //Not using in loopback mode UART_DIS_ABAUD & //Disable ABAUD UART_NO_PAR_8BIT & //8bit data with none for parity UART_BRGH_SIXTEEN & //Clock pulse per bit UART_UXRX_IDLE_ONE& // UART Idle state is 1 UART_1STOPBIT; // 1 stop bit UartCtrl = UART_TX_ENABLE & //Enable UART transmit UART_IrDA_POL_INV_ZERO &//sets the pin's idle state UART_SYNC_BREAK_DISABLED & UART_INT_RX_CHAR & //Interrupt at every character received UART_ADR_DETECT_DIS & //Disabled since not using addressed mode UART_RX_OVERRUN_CLEAR; //UART Overrun Bit Clear ConfigIntUART1( UART_RX_INT_EN & //Enable RX Interrupt UART_RX_INT_PR2 & //Set priority level UART_TX_INT_DIS & //Disable TX Interrupt UART_TX_INT_PR0); //Priority as none IFS0bits.U1RXIF = 0; OpenUART1(UartMode,UartCtrl, BRGVAL); } void SetupIOPins() { //--------------- Pin Assignment ----------------- TRISBbits.TRISB11 = 0; //Pin 22 as output pin for UART TX TRISBbits.TRISB10 = 1; //Pin 21 as input pin for UART RX PPSUnLock; PPSOutput(OUT_FN_PPS_U1TX, OUT_PIN_PPS_RP11); PPSInput(IN_FN_PPS_U1RX, IN_PIN_PPS_RP10); PPSLock; //------------------------------------------------- } void SetupClock() { //Setting N1 to 4 (N1 = n+2); n = N1-2 CLKDIVbits.PLLPRE0 = 0; CLKDIVbits.PLLPRE1 = 1; CLKDIVbits.PLLPRE2 = 0; CLKDIVbits.PLLPRE3 = 0; CLKDIVbits.PLLPRE4 = 0; //Setting M to 32 (M = m+2); m = M-2 PLLFBDbits.PLLDIV0 = 0; PLLFBDbits.PLLDIV1 = 1; PLLFBDbits.PLLDIV2 = 1; PLLFBDbits.PLLDIV3 = 1; PLLFBDbits.PLLDIV4 = 1; PLLFBDbits.PLLDIV5 = 0; PLLFBDbits.PLLDIV6 = 0; PLLFBDbits.PLLDIV7 = 0; PLLFBDbits.PLLDIV8 = 0; //Setting N2 to 2 CLKDIVbits.PLLPOST0 = 0; CLKDIVbits.PLLPOST1 = 0; } void _ISR_AUTO_PSV _U1RXInterrupt() { while(DataRdyUART1()) { RXData[RXCnt] = ReadUART1(); RXCnt++; if((RXCnt > 31) || (RXData[RXCnt-1] == 0x0D)) { for(i=0; i < RXCnt; i++) { while(BusyUART1()); // Wait till TX Buffer has space putcUART1(RXData[i]); } memset(RXData,0x00,32); RXCnt = 0; } } IFS0bits.U1RXIF = 0; //Reset RX Interrupt flag }

 

Output

 

output